I am very happy with my Omada setup. It’s an ecosystem, not a single device. I use an er605 as router and eap610 as AP. I also have a switch, probably you don’t need that, and I now have an Omada controller (you can also host that in as a docker container, so not strictly needed). For wifi you can simply throw another ap somewhere and have excellent Mesh wifi. It’s more complex than a simple consumer router, but also has a lot more functionality.
Out of curiosity, why would that be a problem?
tried with transcoding disabled, no joy, still freezes. Subtitles were also disabled, I rarely watch with subtitles. Edit: I just noticed, when forcing transcoding by limiting the quality (Bitrate) on the client to lower values, it does not freeze
container is mkv, codec says AVC
Checked on transcoding, it happens on direct streaming…
Bitrate varies, some files work, some don’t. Even in one season of a show episode 1 streams perfectly fine, episode 2 freezes every 2 mins.
Bitrate of a file is around 8Mbps, local bandwidth is 1Gbps.
How I’d go above this is dependent on how much storage you expect to be using mid term/until you want/can buy another drive.
Must have 7TB ? Swap the 10tb for 2x4TB, then do 4TB parity 4+2+1TB as Data drives.
Is 3TB enough for the time being? Keep the 10TB and use as parity, 1+2TB as Data drives. When full, go for up to another 10TB as Data.
That second option is more upgradable in the future.
I’m guessing everyone meant Data drives by saying “pool”. In unraid, Data drives are the ones protected by parity, in the array. Pools are “out of the array”, not protected by parity.
When I got started I preferred GUI apps too. The more you use them, the more you get to appreciate cli tools. Meanwhile I find cli tools better, they are just more precise and have a good way to push you to use them correctly. Also they are mostly well documented and even offer “on the fly” help with -h flags or alike… also the get started page of Borgmatic is really well written. Just play around with it ;)
Maybe have a look at urbackup. Gui, “centrally managed”, free…
And please, as mentioned in another comment, have a look at Borgmatic. It makes Borg really easy to use and has some super handy features. Super easy backups to multiple locations by just adding a line in the config… And I just love the healthchecks integration. Set and forget until either healthchecks notifies you of a problem or you really need to recover data.
Can confirm Borg/Borgmatic. Was looking for something good also and Borg is hands down the best. Borgmatic is kind of a wrapper for Borg which makes things even easier. One thing that makes Borg awesome is it’s excellent documentation. Maybe give cli tools a try ;)
I tried fenrus before, kinda liked it, but I remember it to be not so performant.
I had authentik before but I found it to be unnecessarily complicated. Its really a nice one stop shop, doing authentication, authorization, even reverse proxing, but the setup/UI is just … Not very well designed. Or it’s so advanced that it’s very far from the no it background hobbyist user
Would be nice if each user could add their own bookmarks so they could use the dashboard as new tab default.
And how do you disable the editing/configuration in Heimdall?
I just played around a little, and even got it playing nice with authelia quick. But I find it to loaded for me. No bad, it’s looking awesome, but I really just want a few nice looking bookmarks for when the wife forgets what that one service was called again ;)
Two things:
192.135.163.0 is not a private IP… the private range would be 192.168.0.0/16. I guess that’s because you changed the IPs bit maybe better check that
And 0.0.0.0/0 means “all IPs” so it doesn’t really make sense to put the other one there.
Other than that I don’t see anything wrong…
Can you post your config of the client? Remember to redact sensible information.
Then you would need to put that, and only that IP in the allowed IP section.
This would tell the peer with this configuration to send all traffic for the whole 192.168.1.0/24 through the tunnel, not sure that is what OP wants. (Didn’t look at the link though)
The controller does not need to run 24/7. The controller configures the devices and the config remains on the devices. Though, when your devices are adapted by a controller, you cannot access any settings on the devices themselves, only via the controller.
Maybe should add: depending on the network set-up, I’d strongly recommend getting a hardware controller. For me, I have one server hosting all my stuff. I also hosted the controller with docker in this server. Which ends up being a single point of failure, and no way to look into your routing if your server is down/unreachable. I got a hardware controller (oc200) eventually just to separate my interner and network infrastructure from my hosting and service infrastructure.